Best Cisco 300-115 Dumps To Follow About 300-115 Exam

This exam certifies the switching knowledge and skills of successful candidates. They are certified in planning, configuring, and verifying the implementation of complex enterprise switching solutions that use the Cisco Enterprise Campus Architecture.

For More Details:

https://www.certswarrior.com/exam/300-115/

Question: 1

Which two VLAN ranges can you add. modify or delete on a switch'? (Choose two)

A. 1 through 1001

B. 1006 through 4094

C. 1005 through 4094

D. 2 through 1001

E. 2 through 4094

Answer: BD

Question: 2

Which Cisco technology provides network redundancy by combining two physically separate switches to a single logical switch'?

A. VSS

B. IPPS

C. PAGP

D. LACP

Answer: A

Question: 3

Which two commands configure RSPAN to capture incoming and outgoing traffic on a single interface'? (Choose two)

A. monitor session 1 source interface gigabitethernetl/0/2 tx

B. monitor session 1 destination remote vlan 910

C. monitor session 1 source interface gigabitethernetl/0/1 rx

D. monitor session 1 destination interface gigabitethernetl/0/2 rx

E. monitor session 1 source interface gigabitethernet1/0/2 both

Answer: BE

Question: 4

Which feature is enabled automatically when you configure HSRP on an interface?

A. ICMP redirect messages

B. HSRP tracking

C. IGMP snooping

D. HSRP preemption

Answer: A

Question: 5

Which command do you enter to troubleshoot a misconfigured EtherChannel?

A. CORE-SW(config)#spanning-tree etherchannel guard misconfig.

B. CORE-SW(config-if)#spanning-tree guard root

C. CORE-SW(config-if)#spanning-tree loopguard default

D. CORE-SW(config-if)#spanning-tree etherchannel guard misconfig

Answer: A

Question: 6

Which statement about configuring an RSPAN session is true?

A. RSPAN supports, by default, the monitoring of Layer 2 switch protocols.

B. The same RSPAN VLAN is used for a RSPAN session on all the switches.

C. Only the source switch in a session must support RSPAN

D. At least one access port must be configured in the RSPAN VLAN

Answer: B

Question: 7

Which command maximizes system resources for ACLs?

A. sdm prefer default

B. sdm prefer routing

C. sdm prefer access

D. sdm prefer vlan

Answer: C

Question: 8

Which option is a benefit of configuring UDLD on a link between two switches?

A. UDLD removes switching loops.

B. UDLD helps prevent switching loops

C. UDLD provides a backup mechanism for fiber.

D. UDLD determines the best switching path

Answer: B

Question: 9

Which two tasks must you perform to configure DHCP snooping on a device? (choose two)

A. Enable DHCP snooping on the VLAN

B. Enable VRF support for the DHCP relay agent

C. Enable DHCP snooping globally

D. Enable DHCP packet validation on the device.

E. Enable DHCP option 82.

Answer: AB

Question: 10

When the switches in a Cisco Stack Wise stack elect a new master switch, which value is used as the primary selector'?

A. lowest uptime

B. highest MAC address

C. lowest MAC address

D. highhest administrator assigned priority

Answer: D

Question: 11

Which two commands display trunking information on one or more Ethernet interfaces? (Choose two)

A. show interfaces summary

B. show interface trunk

C. show interface brief

D. show interface switchport

E. show interface

Answer: BD

Question: 12

Which command displays the current SDM template?

A. show sdm prefer routing

B. show sdm prefer layer 2

C. show sdm prefer

D. show sdm prefer default

Answer: C

Question: 13

Which statement about SPAN is true'?

A. it uses a specific VLAN to transfer mirrored traffic.

B. SPAN destinations also can be SPAN sources.

C. It is an industry standard protocol for mirroring traffic

D. SPAN destinations participate in spanning tree instances

E. It mirrors traffic from a source port to a destination port on the same switch only

Answer: D

Question: 14

Which two TLVs are included in Cisco Discovery Protocol advertisements? (Choose two)

A. Native VLAN TLV

B. VTP Management Domain TLV

C. Network Policy TLV

D. System Name TLV

E. Inventory Management TLV

Answer: AB

Question: 15

Which command configures ail access ports on a switch to immediately enter the forwarding state when the switch is reset?

A. spanning-tree portfast

B. spanning-tree portfast bpduguard default

C. spanning-tree portfast default

D. spanning-tree portfast bpdufilter default

Answer: A

For More Details:

https://www.certswarrior.com/exam/300-115/

Use Coupon code "20off2018" to enjoy 20% off.